Skip to content

Linksys RE7350 Setup

A dual-band WiFi 6 range extender, the Linksys RE7350 setup is intended to improve wifi coverage in homes and workplaces by removing dead zones. With its EasyMeshTM compatibility and 1.8 Gbps speed support, it guarantees smooth roaming with compatible routers. The RE7350 is easy to set up using the Linksys app and web-based interface, or WPS (Wifi Protected Setup). The Spot Finder function permits users to place the extender for supreme signal strength. It provides fast and dependable internet over bigger spaces by improving connection for numerous devices through the use of Gigabit Ethernet and MU-MIMO technologies.

Linksys Re7350 Wifi Extender Setup Features

  • Support for Dual-Band WiFi 6 increases coverage at up to 1.8 Gbps.
  • EasyMeshTM Compatibility which provides smooth communication with mesh systems.
  • Wifi Protected Setup, or WPS, allows for quick setup with a single knob click.
  • Web-Based Setup access, use the IP address of the extender to configure it in a browser.
  • Linksys App is helpful in setup and administration.
  • The extender may be positioned for the best signal strength with the aid of spot finder technology.
  • A gigabit Ethernet port gives devices connected connectivity.
  • Beamforming and MU-MIMO provide reliable, fast communications between several devices.
  • Compatible with all ISPs and WiFi routers.

Various Ways To Access Linksys RE7350 Setup

Linksys RE7350 Setup WPS

Follow the given points to know about Linksys RE7350 setup with WPS:

  • The Linksys RE7350 should be beavered into a power vent adjacent to your router.
  • Before continuing, validate that the LED becomes firm.
  • Find your primary router’s WPS knob and push it.
  • Press the extender’s WPS knob.
  • When the linking is effective, the LED will flicker and solidify.
  • Place the RE7350 somewhere within range of the router but with poor WiFi.
  • To maximize placement, use the Linksys Spot Finder tool or the LED indication.

Linksys RE7350 Setup Manual

  • The RE7350 next to your router should be turned on.
  • Link to the “Linksys Extender Setup” WiFi network on your device.
  • In the address bar, type “http://extender.linksys.com” or 192.168.1.1.
  • To find accessible networks, adhere to the on-screen directions.
  • Pass in the keyword for the WiFi network that the router is connected to.
  • Give the expanded network a name and a password.
  • After making the necessary adjustments, wait for the extender to reboot.
  • To get the best coverage, move it to a better spot.
  • Connect gadgets to the wider network.

Linksys RE7350 Setup With App

Go through these steps to execute Linksys RE7350 setup with app:

  • The Linksys app is accessible through the App Store.
  • The Linksys RE7350 next to your router should be plugged in and turned on.
  • Open the Linksys app, then sign in or register.
  • Then choose “Range Extender” after tapping “Set up a New Device”.
  • Connect your phone to the RE7350 by following the instructions.
  • After selecting the primary WiFi network, input the password.
  • Create a special name and password for the expanded network.
  • For optimal placement, use the app’s Spot Finder Tool.
  • Attach devices to the extended network and save settings.

Linksys RE7350 Wifi Extender Setup Issues and Solutions

1. WiFi Network Not Detected by Extender

  • Validate that WiFi is turned on on the main router and move the extender closer to it.

2. The Web Setup Page (http://extender.linksys.com) cannot be accessed

  • Establish a direct connection to the network of the extender.
  • Try using a dissimilar browser or remove the cache.
  • As a substitute, use the IP address of the extender.

3. WPS Configuration Errors

  • Make that WPS is supported by the router. 
  • Press the WPS knob on the router and then the extension.

4. An unstable or sluggish internet connection

Minimize interference from other gadgets, such as cordless phones and microwaves.

To position the extension in the best possible spot, use Spot Finder.

5. Extender Continues to Disconnect

  • Use the Linksys online portal to apprise the firmware.
  • lessen the number of devices that are allied.

6. After setup, there is no internet

  • Reconfigure the extender and do a factory reset.
  • Validate that you input the accurate keyword and SSID while setting everything up.

7. Linksys RE7350 blinking blue light

  • The extension should be situated nearer to the router.
  • After ten seconds of unplugging, reattach.
  • First, press the router’s WPS knob, and then the extender’s.
  • Validate that you are using the right password and SSID.
  • Set up again after holding down the reset knob.

Linksys RE7350 Firmware Update

Improved compatibility, security, and performance are guaranteed when the Linksys RE7350 WiFi extender’s firmware is updated. To upgrade the firmware, follow these steps:

Update the Firmware Automatically:

  • Validate that your gadget is allied to the WiFi network of the RE7350.
  • Launch a web browser and type in the IP address of the extender or http://extender.linksys.com.
  • To log in, use your admin credentials.
  • Under Settings, choose Firmware Update.
  • Click Apprise Now and watch for the process to comprehend if there is an apprise obtainable.

Update the Firmware Manually:

  • Click on the Linksys Support page and look up “RE7350.”
  • Use the browser to access the extender settings.
  • Upload the downloaded file after choosing Manual Update under Firmware Update.
  •  After selecting “Start Upgrade,” let the device restart and wait for the installation to finish.

Linksys RE7350 Reset

The Linksys RE7350 may be reset to factory settings, which is helpful for reconfiguration or troubleshooting.

Using a web interface, soft reset:

  • Validate that the RE7350 network is linked to your device.
  • Go to http://extender.linksys.com in a web browser.
  • Select Factory Reset from the Settings menu.
  • After selecting Reset, watch for the procedure to finish.

Hard Reset (Knob Reset):

  • Validate that it is powered on and connected in.
  • Trace the reset hole on the device’s underside.
  • Hold the knob.
  • Let go of the knob and let the extender restart.

FAQs